Lollar Electric

For homeowners

Electrical panel upgrades and service changes

A service change replaces the equipment that brings power into your house so it can safely carry more. Lollar Electric does service changes for homes in the Prescott area, often ahead of an EV charger, a backup generator or an addition.

Residential breaker panel with the cover off, showing branch wiring routed in neat rows down both sides
A home panel with the cover off: each circuit routed and landed in order.

What is the difference between a panel and a service?

The service is the connection from the utility to your house: the wires from the pole or the underground feed, the meter, and the main disconnect. Its size is given in amps. Many older homes have 100 amps or less. Newer homes usually have 200.

The panel is the gray box with the breakers in it. It divides the service into circuits, and each breaker protects one circuit.

Breaker repair, panel replacement or service upgrade?

These are three different jobs.

  • One circuit is the problem. A single breaker that keeps tripping, or one circuit that has gone dead, is usually a repair. Start with troubleshooting and repair.
  • The panel is worn or full. A new panel on the same size service replaces old parts and can give you more breaker spaces. It does not add capacity.
  • The house needs more power. A service change makes the service itself larger. It is the bigger job, and it can involve the meter base, the service wires and the utility.

How do I know if I need a panel upgrade?

Any one of these is a reason to have the panel looked at:

  • Breakers trip often, on more than one circuit.
  • Lights dim when the air conditioner, the well pump or another large motor starts.
  • There is no open space left in the panel for a new circuit.
  • The panel is warm, buzzes, smells hot, or shows rust or scorch marks.
  • The house still has a fuse box.
  • You are adding a large load: an EV charger, a backup generator, electric heat or an addition.

What happens during a service change?

The order is the same on most houses.

  1. Size the service

    We add up what the house runs now and what you plan to add, and work out the service size that covers it.

  2. Permit

    Replacing a panel or changing a service needs a permit. See who issues it.

  3. Power off

    The utility disconnects power at the meter so the old equipment can come out safely. The house is without power while the work is done.

  4. New equipment in

    The new panel goes in, and the meter base and service wires too if the service is being enlarged. Every circuit is moved over and labeled.

  5. Inspection and reconnect

    The building inspector checks the work, and the utility restores power.

Who issues the permit for a panel upgrade?

The permit office depends on where the property sits, not on which electrician you hire. Our service area pages have more on each town.

What should a panel upgrade quote spell out?

Two quotes can only be compared if they cover the same work. Check that each one says:

  • Whether the job replaces the panel only, or makes the service larger as well.
  • Whether the meter base and the service wires to the house are replaced.
  • Whether the permit and the inspection are included.
  • Who arranges the shutoff and reconnection with the utility.
  • What happens if existing wiring has to be corrected to pass inspection.

Panel upgrade questions

Do I need a panel upgrade to install an EV charger?

Not always. A home EV charger needs its own 240-volt circuit. An open breaker space only shows there is room for a breaker. Whether the service can carry the charger is settled by a load calculation, which an electrician does first. See EV charger installation.

How much does a panel upgrade cost in Prescott?

A panel upgrade has no single price. The cost depends on whether the service is made larger, whether the meter base and service wires are replaced, and whether the service is overhead or underground. Use the quote checklist to compare prices, and call Lollar Electric at 928-778-2523 about your house.

Is a fuse box or an old breaker panel dangerous?

Age alone does not make a fuse box or panel dangerous, but old equipment was built for far smaller loads than a house uses today, and worn parts may not trip when they should. A panel that is hot, buzzing, rusted or scorched should be checked by an electrician soon. If you smell burning or see smoke, call 911.

More questions and answers

Where we do panel upgrades and service changes

We do panel upgrades and service changes across the Quad Cities and Yavapai County.

Out of room in the panel?

Call 928-778-2523 and tell us what you want to add. We will tell you what the service can carry.

Page updated

Call nowRequest a quote